- Vous êtes ici : Accéder au Wiki GeoRezo » Accueil : Wiki GeoRezo » Les logiciels en géomatique » Ilwis » digitizr.eng
Ceci est une ancienne révision du document !
Contenu de digitizr.eng à traduire :
1 "Setup Digitizer" @ 2 "Setup Digitizer - Port Settings" @ 3 "Setup Digitizer - Select Port" @ 4 "Setup Digitizer - Automatic Detection" @ 5 "Setup Digitizer - Manual Setup" @ 6 "Setup Digitizer - Size, Resolution and Final Check" @ 7 "Map Referencing - Coordinate System" @ 8 "Locate Fiducial Marks" @ 9 "Map Referencing - Digitizer Control Points" @ 100 "Are these settings correct" @ 101 "Port Settings" @ 102 "Scan Resolution:" @ 103 "pixel" @ 104 "Digitizer Grid Resolution:" @ 105 "Digitizer-Grid Unit" @ 200 "Received:" @ 201 "Number of Received Characters is not constant" @ 202 "Press Button %i" @ 203 "Trying Automatic Detection" @ 204 "Nothing" @ 205 "Button" @ 206 "None" @ 207 "digitizer" @ 208 "coordinates" @ 209 "diff X" @ 210 "diff Y" @ 211 "Minimum three points required" @ 212 "Scale 1:XXXXXXXXXXXX / XXXXXXXXXXXX" @ 213 "Rotation XXXXX.X / XXXXX.X degrees" @ 214 "Not enough points" @ 215 "Singular Matrix" @ 216 "Sigma = %2.1f mm" @ 217 "Scale 1:%1.0f / 1:%1.0f" @ 218 "Rotation %1.1f / %1.1f degrees" @ 219 "Scale 1:%1.0f" @ 220 "Rotation %1.1f degrees" @ 221 "RowCol (pixels)" @ 222 "Photo (mm)" @ 223 "diff Row" @ 224 "diff Col" @ 225 "Grid XY (digitizer grid units)" @ 226 "diff Grid X" @ 227 "diff Grid Y" @ 228 "Specify settings for the selected port:" @ 229 "RowCol (sub-pixel precision)" @ 230 "Photo (mm in camera-system)" @ 300 "BADID: The device identifier is invalid or unsupported" @ 301 "BAUDRATE: The device's baud rate is unsupported" @ 302 "BYTESIZE: The specified byte size in invalid" @ 303 "DEFAULT: The default parameters are in error" @ 304 "HARDWARE: The hardware is not availablen(is locked by another device)" @ 305 "MEMORY: The function cannot allocate the queues" @ 306 "NOPEN: The device is not open" @ 307 "OPEN: The device is already open" @ 308 "IE error %i" @ 309 "Error opening COM port %in%S" @ 310 "Error opening COM port %i (DCB)" @ 311 "Error opening comport %i (State)" @ 312 "Digitizer Error" @ 313 "WinTab driver not found or not active" @ 314 "Error in communication" @ 315 "Error" @ 316 "No valid fiducial marks found" @ 317 "Less than 2 fiducial marks" @ 318 "Incorrect positions of fiducial marks" @ 319 "Incorrect ordering of 4 fiducial marks" @ 320 "Wrong number" @ 321 "Too few fiducials, %i needed" @ 400 "&Manual" @ 401 "&Nr chars" @ 402 "&X Pos" @ 403 "X &Length" @ 404 "&Y Pos" @ 405 "Y &Length" @ 406 "&Flag pos" @ 407 "Flag &Codes" @ 408 "&Metric System" @ 409 "&Lines per mm" @ 410 "&Lines per inch" @ 411 "&X-size (mm)" @ 412 "&Y-size (mm)" @ 413 "&X-size (inch)" @ 414 "&Y-size (inch)" @ 415 "Digitizer Port:" @ 416 "&None" @ 417 "COM&1:" @ 418 "COM&2:" @ 419 "COM&3:" @ 420 "COM&4:" @ 421 "&Coordinate System" @ 422 "Use for Control Points:" @ 423 "&Metric (Projected) Coordinates" @ 424 "&Geographic Coordinates" @ 425 "&Conformal transformation" @ 426 "&Affine transformation" @ 427 "&WinTab" @ 428 "&Baud Rate" @ 429 "&Data Bits" @ 430 "&Parity" @ 431 "&Stop Bits" @ 500 "Map Referencing" @ 501 "Digitize Point" @ 502 "Next Point" @ 503 "Delete Point" @
